Design Swan

Peeling of bathtub paint is a condition that will rundown your bathtub. It is best to take good care of your bathtub. Before you replace it, give the bathtub a fresh coat of paint if it looks a bit worn.

You can do it yourself to save money on a bathtub that has been damaged. It doesn’t matter if the bathtub has small chips or scratches or if it is severely damaged, you can do this project yourself.

8 Steps to fix peeling bathtub paint:

Peeling of bathtub paint is a common thing among many homeowners. This is a problem that can lead to a deterioration of your bathtub.

Design Swan

Step 1: Gather the materials required

The first thing to do to fix a peeling bathtub is to gather all the materials you may need to perform the project. For chip repair, make sure to purchase a two-component epoxy set along with the tools. You can find it in the adhesive repair section at your local hardware store. The kit should include both the catalyst and hardener that you use to mix the epoxy.

Most epoxy chip repair kits come in white colors to match bathtubs. Make sure you choose the right kit for your bathtub. Two kits can be mixed to create the perfect color. Epoxy repair kits work well in bathtubs of all types.

Step 2: Clean the damaged area

The second step is to scrub and clean the damaged area for effective painting. Use a sponge, a tub cleaner, or soap to scrub the affected area. To clean the area that has been chipped, use warm water and dish detergent. Acetone can be used to clean the area.

Acetone will soften the caulk making it easier for you to remove. After cleaning and scrubbing the area thoroughly, dry it with a towel. Rubber gloves are a must as you protect your hands.

Design Swan

Step 3: To paint, remove the old caulk from the drain and the spout.

To keep it out of the way, add the old caulk and drain to the garbage bag. As you remove the caulk, make sure you have a bag nearby so you can easily put it in. You can throw it away since you won’t be using it anywhere. Do not worry if the caulk is not completely removed. You will sand the tub down later.

To prevent them from getting painted, the next step is to remove the drain and spout. You will need a screwdriver to get rid of the drain and water spout. These fixtures can be cleaned during this time before they are returned.

Step 4: bleaching the bathtub

Follow the directions provided on the epoxy kit to mix the two components to bleach the bathtub. You may find an epoxy kit with a stirring stick and a tray for mixing the components. Mix the epoxy using the spoon or the stirring stick in the disposable tray.

Apply the epoxy to the chip using a small spatula, paintbrush or a paintbrush. Spread a thin layer of epoxy over the chip area. Spread the epoxy in one direction. Then, smoothen out any areas where it pools. Disposable items are best when applying epoxy.

Make sure to let the epoxy dry according to the instructions. After it has dried, use sandpaper on the surface to make it smoother like other tub parts. You can add another layer of epoxy to cover the chip if you feel it.

Step 5: Refinishing badly damaged tubs

Get the bathtub refinishing kit from a nearby home improvement center. Make sure the kit includes sandpaper and refinishing paint. Make sure the kit includes a tub cleaner, tub cleaner, brush, roller and primer. The bathroom should be ventilated and the floors covered. Install a fan in the bathroom and open all windows. Protective gear is recommended.

The cleaner provided with the kit can be used to clean the bathtub. The instructions on how to use the cleaner are clear. Next, scrub the tub with the sponge. To remove any stains or scum, rinse the tub.

To remove the old finish from the tub, sand it with sandpaper. You can sand the entire surface using an electric sander, or by hand. Make sure it is smooth.

Step 6: Repair any cracks or chips

After sanding the whole tub, you can check to see if any crack or chips are remaining. Repair cracks or chips with a 2-component epoxy crack fix kit. In a tray, mix the two parts. Use a spatula, or a small brush to apply thin layers of epoxy to cracks or chips in the tub.

Allow the epoxy to dry for at least two to three hour before you start sanding down the patches using 2000-grit paper. This will match the exterior finish of the tub.

Step 7: Applying the paint

Before you start applying the paint, tape the protective sheets on the floor and walls, use the masking tape to secure the plastic sheeting to the floors and walls surrounding the tub. Plastic sheeting can also be used to cover other fixtures such as the sink or toilet. Acrylic paint is best.

Once you are ready, put on old clothes and a respirator. You should wear clothes you are comfortable getting dirty. Safety purposes will be served by the respirator. It is important to be safe from paint fumes. Follow these instructions to prepare the paint properly.

Design Swan

Load the spray gun by following the provided spray gun’s instructions to know how much the paint to load. Keep the lid on the paint in order to prevent the enamel drying out. You can also use rollers and paint brushes if you don’t want to use the spray gun.

Starting at the top, work your way down the tub in a straight line. The spray gun should be kept at eight inches from your tub. Continue the process until the tub is fully painted. Next, paint the tub’s exterior.

Let the exterior of the tub dry after you have completed the painting. The second coat can be applied once the first coat has dried. Allow it to dry for about 15 to 20 minutes. Once it’s dry, apply the second coat.

Step 8: Finishing the tub

Allow the tub to stay alone until it is cured completely. You should not use any water on it or walk in it. For curing time, follow the manufacturer’s instructions. Reattach tub fixtures and remove the tape. Apply the caulk again to the areas where the tub meets with the gun. The bathtub will now be completely fixed.

Air bathtubs are much more durable than traditional bathtubs. You can avoid the hassle of removing the bathtub from the bathroom by installing an air bath.

Design Swan


If you have meant to do something about the peeling paint on the bathtub, grab the tool kit and get started. We’ve thoroughly researched the steps to fix peeling bathtub paint. The steps will make your tub look brand new again.

You can repair the tub’s peeling surface by filling in the cracks and holes, cleaning it, and priming. The moment the surface is dry, you can then repaint it following the manufacturer’s instructions. You can save money by doing it yourself and giving your tub a new look instead of replacing it.

Leave a Reply

Your email address will not be published. Required fields are marked *