Have you noticed hairline cracks on your door? Humidity and temperature fluctuations cause wood to expand and contract, leaving splits on the surface of the door.
If you fix a cracked door early, you can prevent the splits from growing into huge crevices, which would otherwise compromise the door’s energy-efficiency. With a few inexpensive tools and materials, the job should be done in a few hours.
Tools
You will need the following tools and materials:
- Putty knife
- Dremel tool
Materials
- Wood putty or filler
- Epoxy sealer and adhesive
- Wood spline
- Sandpaper
Step-by-Step Guide on How To Fix A Cracked Door
Follow these simple steps to repair cracks on a solid door.
Step 1. Choose between wood putty and filler
Both wood putty and filler can help to repair door cracks but there are slight differences between the two materials.
- Putty is flexible and doesn’t dry hard. This is a good option if you do not plan to sand, stain, or paint your door.
- Opt for filler if your door is already painted and will, therefore, need to be repainted after fixing the cracks. Filler, unlike putty can be sanded and dries quickly.
Step 2. Apply filler onto the crack
Wood filler offers a longer-lasting solution for dealing with door cracks. For the best results, be sure to choose good quality filler.
- Use a putty knife to fill the crack with a small amount of wood filler. Repeat this process for all cracks in the door. Add more filler as needed to cover the entire crack.
Step 3. Allow adequate drying time
- Scrape off excessive filler. The surface doesn’t have to be even—you will sand it later.
- Give the filler enough time to dry. Good quality filler typically has a shorter drying time.
Pro Tip: Use a blow dryer to direct hot air onto the filled-in crack for the filler to dry faster.
Step 4. Sand the surface
(*7*)
For a smooth finish, you will need to sand the surface where you applied the filler.
- Use gentle strokes to sand the target area using medium grit sandpaper (60-100 grit) until the surface is even.
- For a longer-lasting fill, reapply the filler and allow it to dry before sanding the surface again. Always use gentle strokes to avoid scratching the paint too much or causing dings on the door.
Step 5. Paint the surface
- Select a similar tone of paint to apply to the sanded area.
- Be sure to use the correct painting technique to avoid leaving paintbrush marks on the door. If possible, paint using a roller with a velour cover instead of using a paintbrush. Rollers offer a more finished look compared to paintbrushes. That being said, a paintbrush is easier to use if you are painting the grooves of a paneled door.
- Allow the paint to dry.
Step 6. Use epoxy glue for medium-sized cracks
If you are dealing with a medium-sized crack, wood filler or putty will not fix the damage. Opt for a stronger compound such as an epoxy adhesive.
- The epoxy sealer should be used to fill the crack. The sealer helps the adhesive to adhere.
- Next, squeeze a bead of epoxy adhesive into the crack. The epoxy adhesive will expand to fill the crack. Therefore, a little does go a long way.
- Let the glue dry then apply a final coat of sealer. Allow the sealer to dry.
- Use fine sandpaper (120-220 grit) to buff the surface. Paint or apply stain to the surface as needed.
Step 7. Fix large cracks using wood splines
To fix large splits on the door, you will need more than just glue or filler. Inserting a wood spline into the split offers the most lasting solution.
- Use a Dremel tool to clean and create space in the split so that the wood spline fits snugly.
- Then, insert the spline into the split to test for size. The spline should be adjusted in size until it fits snugly into the crack.
- Take out the spline, and then fill the crack with high quality wood glue. Insert the spline in the crack. Use a rubber mallet to gently push the spline deep into the crack.
- You can now chisel away any protruding edges to ensure that the spline meets the door. Allow the glue to dry before sanding the area.
- As needed, paint or stain the door.
That’s is all there is to fix a cracked door. Now your door will look brand new.
Extended Tips
Below are additional tips to help you get the most from this project.
- Prep your work area
Because this project involves sanding and painting, be sure to protect your floors with a dust cloth. You do not want filler, paint, or wood chaffing to ruin your floor or carpet.
- Clean the door
Before getting started, wipe the door to rid it of dust. Filler, putty, and even glue will not adhere well to a dusty surface. Be sure to wipe the door after sanding and before painting or staining.
- Use putty for stained doors
To fix hairline cracks on a painted door, it is best to use wood putty, as you won’t have to sand the surface. Simply fill cracks with a small amount of putty, wipe off any excess, and you are good to go.
- Replace cracked plywood
Some interior doors are made of thin sheets of plywood, which is prone to cracking. Some cases will require you to apply filler or putty, but this won’t always solve the problem.
Consider replacing the whole sheet of plywood if new cracks develop or old ones continue to open. Removing the old plywood should be easy given that the sheet is attached to the doorframe by a bead of glue.
Summary
Door cracks are common and are usually an easy DIY fix. Small hairline cracks can quickly turn into gapping splits, which may require additional work or even replacement of the entire door. Regular maintenance and proper care will help to prevent expensive repairs.
Do you have a cracked door in need of repair? Leave your comments and questions below—we’d love to hear from you!
